Search found 1118 matches
- 23 Feb 2014 14:58
- Forum: MAGROM
- Topic: Available for order
- Replies: 27
- Views: 35364
Available for order
Hi Guys, I have worked out the final cost of the PCBs, including shipping to the UK, EU and USA. I had originally intended to only supply the bare PCB as the other parts are available in the UK without too much difficulty from the likes of Maplin, Rapid, ebay etc. The only exceptions perhaps are the...
- 22 Feb 2014 03:11
- Forum: MAGROM
- Topic: The finished "product"
- Replies: 4
- Views: 9031
Re: The finished "product"
Hi Mark,
I'll include your free sample with the two you were going to buy . . . .
Oh, I forgot to mention, the price has gone up by 50%
I'll include your free sample with the two you were going to buy . . . .
Oh, I forgot to mention, the price has gone up by 50%
- 21 Feb 2014 22:33
- Forum: MAGROM
- Topic: The finished "product"
- Replies: 4
- Views: 9031
Re: The finished "product"
So, my first forray into PCB manufacture seems to have been a success . . . . One small "glitch", Martin spotted that I had not labelled the jumper positions as "MTX500", "MTX512" and "RS128", so you need to know what the correct link position is for the machi...
- 21 Feb 2014 22:29
- Forum: MAGROM
- Topic: The finished "product"
- Replies: 4
- Views: 9031
Re: The finished "product"
And what's more - it even works !
This is Martin's board, assembled and running MAGROM software version 1.0
This is Martin's board, assembled and running MAGROM software version 1.0
- 21 Feb 2014 22:27
- Forum: MAGROM
- Topic: The finished "product"
- Replies: 4
- Views: 9031
The finished "product"
The PCB has been manufactured !
- 18 Feb 2014 23:58
- Forum: HARDWARE
- Topic: Embarrassing newbie questions
- Replies: 32
- Views: 43479
Re: Embarrassing newbie questions
If it is "cemented in", that would be a first! Remove both end plates and inspect between the bottom of the PCB and the base of the case, there should be about 5mm of a gap. If you hold it up to eye level, you should be able to see underneath the board. The rubber insulator mentioned earli...
- 17 Feb 2014 22:16
- Forum: HARDWARE
- Topic: Embarrassing newbie questions
- Replies: 32
- Views: 43479
Re: Embarrassing newbie questions
A question that I know you have answered already, but, just to be sure . . . You have removed the single bolt that goes through the bottom of the case, through the regulator and onto the heatsink? And, just to clarify, the regulator heat sink sits in a gap in the plastic rear panel, they both need t...
- 17 Feb 2014 22:10
- Forum: GENERAL DISCUSSIONS
- Topic: FREE Electronic Components !!! - no, this isn't spam !
- Replies: 54
- Views: 49143
Re: FREE Electronic Components !!! - no, this isn't spam !
OK, sorry, meant to e-mail it, but
you can download it from here :-
http://www.primrosebank.net/computers/m ... txplus.htm
the link is about half way down the page
regards
Dave
you can download it from here :-
http://www.primrosebank.net/computers/m ... txplus.htm
the link is about half way down the page
regards
Dave
- 16 Feb 2014 15:47
- Forum: GENERAL DISCUSSIONS
- Topic: FREE Electronic Components !!! - no, this isn't spam !
- Replies: 54
- Views: 49143
Re: FREE Electronic Components !!! - no, this isn't spam !
Hi Guys,
Lez has placed the order now, as the parts are coming from China, it may well be a few weeks before they arrive and I can distribute them
regards
Dave
Lez has placed the order now, as the parts are coming from China, it may well be a few weeks before they arrive and I can distribute them
regards
Dave
- 15 Feb 2014 00:41
- Forum: GENERAL DISCUSSIONS
- Topic: FREE Electronic Components !!! - no, this isn't spam !
- Replies: 54
- Views: 49143
Re: FREE Electronic Components !!! - no, this isn't spam !
Certainly! - put me at the top of the list . . .
Once you have ironed out the wrinkles in the design
Once you have ironed out the wrinkles in the design